Statistical Piezotronic Effect in Nanocrystal Bulk by Anisotropic Geometry Control

Utilizing inner-crystal piezoelectric polarization charges to control carrier transport across a metal-semiconductor or semiconductor–semiconductor interface, piezotronic effect has great potential applications in smart micro/nano-electromechanical system (MEMS/NEMS), human-machine interfacing, and nanorobotics. However, current research on piezotronics has mainly focused on systems with only one or rather limited interfaces. Here, the statistical piezotronic effect is reported in ZnO bulk composited of nanoplatelets, of which the strain/stress-induced piezo-potential at the crystals’ interfaces can effectively gate the electrical transport of ZnO bulk. It is a statistical phenomenon of piezotronic modification of large numbers of interfaces, and the crystal orientation of inner ZnO nanoplatelets strongly influence the transport property of ZnO bulk. With optimum preferred orientation of ZnO nanoplatelets, the bulk exhibits an increased conductivity with decreasing stress at a high pressure range of 200–400 MPa, which has not been observed previously in bulk. A maximum sensitivity of 1.149 µS m⁻¹ MPa⁻¹ and a corresponding gauge factor of 467–589 have been achieved. As a statistical phenomenon of many piezotronic interfaces modulation, the proposed statistical piezotronic effect extends the connotation of piezotronics and promotes its practical applications in intelligent sensing.     

Hematite crystal growth in high-temperature lead-free multicomponent alkali borosilicate glass frit for red overglaze enamels

To elucidate the crystal growth process of hematite in high-temperature lead-free multicomponent alkali borosilicate glass, which is essentially important to control the color of red overglaze enamels, frit and hematite mixture is heat-treated and subjected to microscopic observations. Hematite particles slightly grew due to sintering at low temperature. Once the glass matrix formed near the softening point of frit, hematite dissolved into glass fluid. Hematite crystal growth concomitantly ensued with decrease in the number of hematite particles via Ostwald ripening as the temperature increased. The grown particles exhibited an anisotropic morphology with straight outlines reflecting crystal planes, the morphology of which is completely different from those grown by sintering and particles prior to heating. These results suggest that comprehensive understanding of frit and hematite from the perspectives of glass science and chemistry as well as powder technology are important to truly control the color of red overglaze enamels.     

Additive manufacturing,quasi-static and dynamic compressive behaviours of ceramic lattice structures

Ceramic lattice structures (CLSs) are used for construction in common and extreme environments because of the extraordinary properties of ceramics. In this study, we designed and additively manufactured CLSs with distinct structural parameters to explore their quasi-static and dynamic compressive behaviours in detail. It was demonstrated that both the relative density (?ρ) and inclination angle (ω) had a significant impact on the quasi-static and dynamic mechanical properties of the CLSs. Furthermore, the mathematical relationships between the quasi-static compressive properties, including quasi-static compressive strength (QS), quasi-static Young’s modulus (QY), and quasi-static energy absorption (QE), versus ?ρ and ω obeyed the Gibson–Ashby and Deshpande and Fleck models, respectively. It was revealed by experiment and simulation that as the stiffness increased, the quasi-static failure mode of the CLSs changed from a parallel-vertical-inclined mixed mode to a parallel-vertical mode. In addition, the relationship between the dynamic mechanical properties of the CLSs versus ?ρ and ω also followed the Gibson–Ashby and Deshpande and Fleck models. The exceptional dynamic increase factor indicated that CLSs are highly suitable for extreme environments. These findings will aid in the research and development of customised additively manufactured CLSs.     

Flash cosintering of a lanthanum strontium cobalt ferrite nanofibre/Gd-doped ceria bilayer structure

For solid oxide fuel cells, an important structural requirement is that the electrolyte layer needs to be dense and the electrode layer porous, which is difficult to obtain by conventional cosintering. In this work, flash cosintering of a double layer structure consisting of a Gd-doped ceria substrate with a lanthanum strontium cobalt ferrite nanofibre coating is investigated. Experimental and finite element modelling results reveal that when the LSCF layer is connected to the electrode, the heat is concentrated in the LSCF layer, which leads to a huge temperature gradient and introduces severe cracking. When the LSCF layer is electrically isolated from the electrode, the heat is concentrated in the GDC layer, and the temperature gradient is dramatically reduced. In this situation, the density of GDC can reach 92.86% while a high porosity of 52.26% is maintained in the LSCF layer, which is higher than that of the conventional cosintered sample.     

Sealing behaviour of glass-based composites for oxygen transport membranes

In this study, seven different filler materials in different proportions were added to a Ba-Ca-Si glass matrix “H” to investigate new sealant with higher thermal expansion coefficient (CTE) value and good sealing performance for application in oxygen transport membrane (OTM). SrTi_0.75Fe_0.25O_3-δ (STF25) was used as an OTM, and the sealing partners were ferritic steel Aluchrom and pre-oxidized Aluchrom. Compatibility tests were carried out to investigate the feasibility of the composites. Higher CTE values were found in dilatometer tests on composite samples by adding 40 wt% Ag (HAg40) and 30 wt% Ni-Cr (HNC30). Gas-tightness measurements of sandwiched samples produced appropriate helium leakage rates in the range of 10^?6 mbar·l·s^?1. Sealing behaviour of sealants HAg40 and HNC30 were investigated by joining STF25 and as-delivered/pre-oxidized Aluchrom together. Scanning electron microscopy (SEM) on cross-sections of the joints revealed a homogeneous microstructure and good adherence of the glass sealants to support metals and STF25.     

Nanograin–glass dual-phasic,elasto-flexible,fatigue-tolerant,and heat-insulating ceramic sponges at large scales

Ceramics are considered intrinsically brittle at room temperature, which is mainly attributed to the limited availability of crystallographic slips and pre-existing geometrical flaws. Moreover, the lack of flexibility has severely hindered many high-end applications of ceramic materials. Here, we produce ceramic sponges that are simultaneously ultra-light, elasto-flexible, thermally insulating, and can fully recover from large deformation with a near-zero Poisson's ratio. These spongy materials also possess superb fatigue resistance without the accumulation of damage or structural collapse for 10,000 large-scale compressive or buckling cycles. We demonstrate the exceptional flexibility is enabled by the elastic distortion of nanograin–glassy dual phase and the fiber bulking in open-cell three-dimensional structure. Moreover, these spongy materials possess superior temperature-invariant superelasticity from deep cryogenic temperatures (−196 °C) to high temperature (1500 °C). Our study not only developed mechanically reliable lightweight ceramics for numerous extreme applications, but also provided new theoretical insights into the origin of flexibility in polycrystalline ceramics.     

Pressure-less joining of alumina ceramics by the reaction-bonded aluminum oxide (RBAO) method

The present work demonstrates a pressure-less and reliable joining technique for alumina ceramics through a reaction-bonded aluminum oxide (RBAO) method. Effective joining relies on the RBAO mechanism, in which Al particles are converted to alumina through oxidation and bond with alumina particles from the parts to be joined upon sintering. Alumina ceramics in a green state were successfully joined with the use of an Al/Al₂O₃ powder mixture as an interlayer. The oxidation behavior of the Al particles was confirmed by thermogravimetry and X-ray diffraction analyses. Joining was performed in ambient air at 1650 °C for 2 h without applying any external pressure. Microstructural observations at the joining interfaces indicated a compact joining. The joining strengths were assessed by determining the biaxial strengths at room temperature, and the joined samples exhibited no fractures at the joining interfaces. Moreover, the joints had a strength of almost 100 % when compared with those of the parent alumina ceramics.     

Reversible formation-melting of nano-crystals in supercooled oxyfluoride germanate liquids

The nanocrystals play a critical role in generating and affecting functionalities of glass materials. Therefore, scientists have made considerable efforts in clarifying microscopic mechanisms of nanocrystal formation in glass to obtain the desired type of nanocrystals. However, the phase transitions of nanocrystals during heating have not been well understood. Here we report on a discovery of the reversible melting-formation of nanocrystals in an oxyfluoride germanate glass during heating-cooling circles. Using a differential scanning calorimetry (DSC), we detected a striking endothermic event at 925 K during heating, after the glass underwent a DSC upscan to a temperature between 925–986 K and subsequent cooling. Based on Raman spectroscopy, X-ray diffraction and transmission electron microscopy, the endotherm is attributed to the melting of nano-crystal BaGeF₆ (˜20 nm). An exothermal response was observed at 890 K during the DSC downscan, implying the re-formation of BaGeF₆ nano-crystals. This suggests that the melting-formation of BaGeF₆ nano-crystals is a typical first-order transition.     

Fabrication of BSCF-based mixed ionic-electronic conducting membrane by electrophoretic deposition for oxygen separation application

Ba_0.5Sr_0.5Co_0.8Fe_0.2O_3-δ (BSCF), which exhibits a high mixed oxide ionic-electronic conduction, was used for the fabrication of an oxygen separation membrane. An asymmetric structure, which was a thin and dense BSCF membrane layer supported on a porous BSCF substrate, was fabricated by the electrophoretic deposition method (EPD). Porous BSCF supports were prepared by the uniaxial pressing method using a powder mixture with BSCF and starch as the pore-forming agent (0–50 wt.%). The sintering behaviors of the porous support and the thin layer were separately characterized by dilatometry to determine the co-fired temperature at which cracking did not occur. A crack-free and thin dense membrane layer, which had about a 15 μm thickness and >95% relative density, was obtained after optimizing the processes of EPD and sintering. The dense/porous interface was well-bonded and the oxygen permeation flux was 2.5 ml (STP) min⁻¹ cm^-2 at 850 °C.